Switch to full site
Post your pictures here!
Post a reply

Consolidated War Wagon build thread.

January 11th, 2014, 1:05 am

I have the grill guard and the taillight covers installed. The rear bumper guard would normally require removing the hitch receiver (something I found only after calling the company after getting ready to put it on). It's a shame, since without my receiver it would be a one man job in about ten minutes. I did find a local shop in Little Rock willing to weld on some brackets so the rear bumper guard can use existing receiver hardware instead of requiring that I remove the support for the back bumper. I'll have those pics up once they're on.

Until then, I can at least show off the grill guard.

Image

Image

#Blackhorse Grille Guard
Last edited by Meatloafmountain on July 21st, 2017, 12:13 pm, edited 9 times in total.

Re: Blackhorse grill guard, rear bumper guard and taillights

January 11th, 2014, 12:49 pm

:thumb:

Re: Blackhorse grill guard, rear bumper guard and taillights

January 11th, 2014, 7:22 pm

I love this! On their website it doesn't say that this won't fit a '12 E. Any ideas why?

Re: Blackhorse grill guard, rear bumper guard and taillights

January 11th, 2014, 7:27 pm

I bought off of carid.com. With the exception of one item (a pintle hook) what they claim will fit my '12 has been spot on.

The instructions for every Blackhorse product I've bought have been squirrely, though. Like mentioning this item will only fit an '08-'10 or some other garbage, but I haven't had problems other than the rear bumper guard.

Re: Blackhorse grill guard, rear bumper guard and taillights

January 13th, 2014, 9:52 am

That looks really good! :thumb:

Re: Blackhorse grill guard, rear bumper guard and taillights

January 13th, 2014, 9:54 am

Very nice E Meatloafmountain :shades: :thumb: :thumb:

Re: Blackhorse grill & rear bumper guards and taillights (pi

January 16th, 2014, 2:11 am

I just installed the steel craft rear bumper guard with my hitch.it must depend on the hitch and guard. What hitch do you have on?

Re: Blackhorse grill & rear bumper guards and taillights (pi

January 16th, 2014, 12:30 pm

Here's the other pictures I promised. More of the grill guard:

Image

Image

RestingSword wrote:I just installed the steel craft rear bumper guard with my hitch.it must depend on the hitch and guard. What hitch do you have on?


1 1/2 inch. It's not the 2.

This is where Blackhorse had their installation holes set and where the hitch receiver interfered with them. As I stated earlier, without the hitch receiver this would have been a ten minute, one man job.
Image

Brackets that were welded on to take advantage of hitch receiver hardware.
Image


#Blackhorse Grille Guard
#Blackhorse Taillight Guards
#Blackhorse Rear Bumper Guard
Last edited by Meatloafmountain on July 21st, 2017, 12:13 pm, edited 6 times in total.

Re: Blackhorse grill & rear bumper guards and taillights (pi

January 16th, 2014, 2:40 pm

RestingSword wrote:I just installed the steel craft rear bumper guard with my hitch.it must depend on the hitch and guard. What hitch do you have on?


Just a his pictures show, it seems to interfere with the factory hitch. However im sure this would work flawlessly with many aftermarket hitches.

Nice install! I like it! :thumb:

Re: Blackhorse grill & rear bumper guards and taillights (pi

January 16th, 2014, 3:14 pm

While I don't get to use the hitch with the rear bumper guard, all I have to do is take off four bolts to mount or tow something. Sure, it took a bit more time and money, but I get to have the guard AND the hitch at the end of the day.
Post a reply